Item UMN9



With shoulder strap fixing screw, a copy of Instruction manual, mono to stereo jack adapter and a new roll of tape that was used to line up the recorder, now has 1 & 8K at -8dB test frequency, and some music to test the playback, and a empty spool.

This 4.L has been modified and has a announcements microphone so slate numbers can be added to start of recording, there is a push button between the Line input and Microphone input controls and above is the microphone, the preference tone generator is on the filter switch, and has a 400 Hz tone

The machine has the following features:
1 switchable microphone inputs that has 50 or 200 Ohm Dynamic, Ribbon, T powered or Phantom powered and 2 x Dynamic, Ridden or microphones with internal battery, a Line input on banana plugs or the 6 pin Tuchel ASS socket, It has Direct or off Tape monitoring and metering, Monitoring selector with monitor speaker and level control, Manual or Automatic recording, headphone monitoring with level control, it has 1 & 2 high pass and 1&2 LAF low freq attenuation filters with Reference generator set a -8dB, It has 3 Taps speeds- 38, 19, 9.5cm/s (15-7.5-3.75ips). 50 Hz strobe roller, manual or auto recording level, Low Frequency Attenuation, Metering with battery test. It has full set of Ruby tape guides, Silicon rubber pinch wheel and drive belts, can run 7" tape spools with the lid open. It also has a nice clean battery compartment.

This is a full track mono CCIR recorder that is with 50 or 60 Hz full Pilot sync

BELOW RIGHT, See pilot link plug socket , above the pilot link socket and handle fixing screw are the two large case opening screws, please note; only unscrew 3 or 4 turn do not take right out, or parts could fall into the recorder, so switch off before opening.

ABOVE LEFT, 2 microphone inputs 3 pin XLR socket for Dynamic microphone, but you can change these plug in microphone pre amps and have "T" powered, or if you can find them a phantom 58 volt preamp

Line Input on a ACC socket is a 6 pin Tuchel plug or 4 mm banana plugs. The VOL is the playback level control, next to the handle fixing screw

ABOVE RIGHT, The 4 mm banana sockets are 4.4 volts output at 600 ohm if you feed this output to a Stereo Nagra you must use the QCSE lead or a copy with a 47K ohm pad. Or use the 7 pin MIXER socket that has a Playback or Direct output, leads can be made to order. For the POWER PACK, you can use the 24 volts ATN power supply, the 35 volts ATN 2 or ATN 3 power supplies, or the UAP11 or UAP12 power supply on main page,

The back of the recorder is not good and has battery corrosion stains, dents and scratches on the bracket feet and hinges. See below.

Above The battery box is in good order.

Above Left :- Tape head are good condition, and the recorder it has a new pinch wheel.

No head loss adjustment was not needed when lining up the tape bias EQ and playback, this recorder is set up for SM911 & LPR35 that I have selected as closest to AGFA 468 or 368, Zonal 468 / 368 and BASF 468 or 368,

Above Right : The SM911 STD play tape is setup for STD on the speed control, and the LPR35 is set up to use on LN on the speed control. If you are recording on SM911 and switch to LN you will have a 6 dB HF lift, or the other way around a 6 dB HF cut


ABOVE RIGHT there is 1 x switchable Microphone pre-amps and 1 x Dynamic microphone preamp see two behind the meter, and one Dynamic Microphone pre-amps on the battery box

ON THE BATTERY BOX, This Recorder is fitted with a Nagra 50/60Hz Crystal Pilot Generator, it is a full pilot sync recorder, so if you need to run the Nagra in sync with a camera you can, but if you don't need it just unplug the pilot link plug in the right hand side of the nagra

The recorder works from 12 x U2 batteries or external ATN mains supply (not included) see accesses 2 for power supplies

Nagra is the best reel-to-reel tape recorder ever made with the best of Swiss engineering that you are never likely to see again.
One of the joys of owning a Nagra is that it is an all in one over the shoulder recorder and when you switch it on you know it's going to work and give you a professional quality recording in any conditions.

Please note: -The Perspex lid is very good but there are some scratches, and there are some battery corrosion stains and dents in the back and bottom of the case, but it has not effected the working of the recorded.

Extras, mods and updates with this recorder click to find out more = 11

To buy this item please telephone: Mike Harris 01932 241948 or Email,